FLASH 2 ECU PROGRAMMING TOOL INSTALL
FLASH 2 ECU PROGRAMMING TOOL UPDATE
FLASH 2 ECU PROGRAMMING TOOL DRIVER
FLASH 2 ECU PROGRAMMING TOOL SOFTWARE

If real reading is not available, KESSv2 automatically downloads the Original File from the Alientech Data Bank.

FLASH 2 ECU PROGRAMMING TOOL SOFTWARE

This may require you sending in your ECU to us.Designed for K-Suite 3 and more! A single management software to remap ECUS and TCUS, managing your tools, protocols, and activations. In the event your computer dies, vehicle battery dies, or another issue arises during programming, we can assist you in the recovery process. Select this file and the same steps will be followed. To flash your vehicle back to stock, use the ORIGINAL file we send you but do Recover ECU Memory instead. Unplug everything and start your vehicle. Step 9 вЂ“В Your programming has been completed. Step 8 вЂ“В Turn your vehicle off and then click the Ignition is Off button. Do not turn anything off, let your computer go to sleep, or battery die! Step 7 вЂ“В The ECU programming sequence will go through. Click open and the programming process will begin. Then select the tuned file from your computer where it was saved. Step 4 вЂ“В Click Software Options and then check the button that says вЂњDo Not correct the checksumвЂ¦ Hit OK. Once you receive your file back, relaunch the program, turn your vehicle ignition on, and follow steps 1 вЂ“ 3 and proceed below. At this point you can turn everything off and wait for us to send you back your tuned file. Once done, upload this imageВ and your vehicle information using upload formВ ( CLICK HEREВ UPLOAD ). Take a screen shot of this image on your computer showing the software number. Once the cable is locked, it cannot be used on any other vehicles. Step 3 вЂ“ Click the next button and lock your cable to this VIN and protocol. Step 2 вЂ“ You will see an вЂњerrorвЂќ like the screenshot below. Step 1 вЂ“В Launch the program and with the cable connected to the vehicle and your computer, follow the prompts. We will then find a matching software number for your vehicle and send you back a tuned file. Do a screenshot of STEP 3, then upload that jpg, png, gif, or bmp to us. Connect to your vehicle and go through the prompts. NOTE: The Canam RotaxВ ME17 ECU can only be ID and not read out. Please make sure to disable ANY antivirus software and screensavers for the reading out and flashing process. We do recommend turning off any virus protection, screen savers, and closing all other programs during the writing process.

Email Address вЂ“ Once you read out your car, you will need to send us your file ( CLICK HEREВ UPLOAD YOUR FILE ).В We will then return your tuned file to this same email address unless otherwise specified.

We recommend this for those that donвЂ™t drive their vehicle regularly or may have a battery with low voltage.

Battery Charger вЂ“ It is highly recommended to have a battery tender or battery charger on the car during the read and write process.

FLASH 2 ECU PROGRAMMING TOOL DRIVER

Windows 8 and 10 no longer need the driver deactivation done (5/31/16)! If you have a issue with the driver, you can download the driver separately hereВ or follow the old driver deactivation process hereВ вЂ“ ( CLICK HERE for tutorial).

FLASH 2 ECU PROGRAMMING TOOL INSTALL

Each OS does install drivers differently so if you encounter a problem, please contact us. Windows Vista, Windows 7 are acceptable and there are no RAM requirements.

FLASH 2 ECU PROGRAMMING TOOL UPDATE

Once you install the program, access your device manager and update the driver or replace it with this one here.

Windows 7 requires a different driver.

Because you need to connect the cable from your car to your computer, a Laptop or Tablet is required and should be plugged in while doing the process. This can be any PC and we haveВ heard of MacвЂ™s working if booted up as a Windows machine.

Computer вЂ“ You need to have a computer to install the flash client and connect the USB cable to.

The software is available on the download link below. This is program is installed like any program on your computer as a.

Flash Client вЂ“ The software application that allows you to read/ID and write via your OBDII port.

It uses a mini USB to standard USB cable that plugs into your computer.

Flash Cable вЂ“ This is included in your VRTuned Flash Kit.

Flash 2 ecu programming tool